Commit Graph
4 Commits
Author SHA1 Message Date
yuanyuanxianganddeepseek-flash 46f4bf2dfb Fix: Make the WebSocket transport reachable and bounded on every platform
The POSIX clients were built without a connection config - Linux, macOS and
Android all construct IOCPClient without the injected CONNECT_ADDRESS - so
ConnectServer saw protoType -1 and quietly dialled the master port in plain
TCP. Setting protoType to WS in their settings did nothing and logged nothing,
and since CLIENT_CAP_PROTO_SWITCH is Windows-only the server could not move
them either. Give the client a SetDefaultProto() for that construction path
and call it from all three mains before the reconnect loop, with a one-shot
log when neither a conn nor a default protocol is available so the silent
fallback becomes visible next time.

Bound what a peer can make the client read. ReadHeader accepted the 8-byte
extended length and rejected only the sign bit, so a frame length of nearly
2^63 kept the connection streaming into a frame that would never end - alive
but never delivering another packet. Cap single frames at 256 MB, the same
value ServerWsSession already applies to client frames, and drop the
connection past it; real traffic is far below that.

Stop Reset() from writing the receive thread's frame state. Disconnect() can
run from the heartbeat or command thread, not just the receive thread, so
Reset() now only flips the atomic ready flag and a new ResetFrames() clears
m_remaining, m_masked and m_maskPos from Handshake() alone, before the
receive thread starts reading the socket. Those fields keep a single owner
without adding a lock to the receive hot path.

Finish a dead WS session instead of leaving it to the keepalive timer. When
the session had closed but wsState was still WS_Ready, sends were dropped and
nothing woke the pending recv, so a peer that closed and then went quiet held
the context for the 3-minute keepalive. shutdown() the socket there so the
recv returns zero bytes and the normal -2 teardown runs; RemoveStaleContext
would deadlock against the caller's own IoRefCount and can hand back a reused
context.

That shutdown only finishes the connection if a zero-byte read still tears it
down, and on the plain path it no longer did. DispatchPlain answers an empty
buffer with "handled", so a peer's FIN left the connection in CLOSE_WAIT
until keepalive - holding an IOCP context, a pending WSARecv and a rate-limit
slot - where the pre-WS code called ParseReceivedData and tore down at once.
Restore that teardown on the TLS_Plain branch, matching the other two. Checked
against a Debug server: a plain socket that half-closes used to sit in
CLOSE_WAIT with the peer's recv timing out, and now disappears immediately
with recv returning zero.

Two smaller cleanups from the same review. Give the WS upgrade its own prefix
buffer (wsPreClassify) instead of borrowing the TLS sniffer's, which was
serially reused for two state machines and read as if it were one. And stop
deriving the build dialog's protoType from the combo box index: items now
carry the protocol value as item data, keyed off the index AddString returns,
so inserting an option in the middle can no longer write the wrong number into
the generated client without any error. ApplyProtoSwitch loses its bool
return, which contradicted its own side effects and was ignored by every
caller.

Co-Authored-By: deepseek-flash
2026-10-30 19:15:14 +01:00
yuanyuanxiang d4f312c9d8 Feature: Tunnel the device protocol through a reverse proxy over WebSocket 2026-10-30 17:21:42 +01:00
yuanyuanxianganddeepseek-v4-pro 96b9eea70a Feat: One-way TLS transport for the MFC server
Add optional one-way TLS to the MFC server (server/2015Remote) so the device
port can serve both TLS clients and legacy plaintext clients on the same port,
mirroring the Go server.

Server: on a connection's first bytes, sniff for a TLS ClientHello (0x16 0x03
+ handshake type 0x01). When [tls] Enabled=1 and the identity loads, hand the
socket to a short-lived blocking handshake thread (Option A) running Schannel
AcceptSecurityContext, then decrypt on recv and encrypt on send; plaintext
connections replay the sniffed bytes straight into the existing parse path, so
the plaintext code path is otherwise unchanged. The identity is loaded once
from [tls] CertPath/KeyPath as PEM + CNG (PKCS#8) — the same key pair the Go
server uses — and a missing [tls] section, an empty value, or a load failure
leaves plaintext serving intact and fail-closes any TLS ClientHello.

Also fix two transport-reliability bugs that surfaced end-to-end:
- send path: encrypt only the freshly appended plaintext tail and post a
  single IOWrite wake-up guarded by a bSendPending flag, so back-to-back small
  sends (terminal resize -> COMMAND_NEXT -> resize) no longer run concurrent
  WSASends over the same mutable buffer (client saw DecryptMessage failures,
  with WSAGetLastError() = 6001 / ERROR_DECRYPTION_FAILED);
- client Recv: keep the handshake's unconsumed tail bytes in m_raw and drain
  them before the next recv, and log the real SECURITY_STATUS on
  DecryptMessage failure instead of the stale Winsock error.

Co-Authored-By: deepseek-v4-pro
2026-10-15 13:48:27 +02:00
yuanyuanxianganddeepseek-v4-pro ca0d7626d2 Feat: One-way TLS transport for the device port
Add optional one-way TLS on the device port (6543), enabled per client via a
pinned trust anchor, so new clients encrypt their transport while legacy
plaintext clients keep working unchanged.

Server (server/go): sniff each accepted connection and wrap TLS peers
(ClientHello 0x16 0x03 + handshake type 0x01) in crypto/tls with MinVersion
TLS 1.2; everything else stays on the plaintext path. TLS is enabled only when
both YAMA_TLS_CERT and YAMA_TLS_KEY are set, and a cert/key load failure fails
startup loudly rather than silently serving plaintext.

Client (client/, Windows): Schannel one-way TLS. When the trust anchor is
present — registry value Software\<exehash>\settings\tls_cert (REG_SZ holding
the PEM), with fallback to settings.ini [settings] tls_cert or yama-ca.pem
beside the exe — every outbound connection (main + sub-connections) completes
a TLS 1.2 handshake before the app protocol and is strictly pinned to that
anchor via a chain engine with hExclusiveRoot; any handshake/cert failure is
fail-closed (no plaintext downgrade). Send uses EncryptMessage; Recv uses
DecryptMessage and reads plaintext from the stream-mode DATA segment (bufs[1])
rather than the record header.

Co-Authored-By: deepseek-v4-pro
2026-10-14 21:10:21 +02:00